Shri Kanha Stainless Limited targets 0.08-mm premium niches
Key highlights
- SKSL says it can produce 0.08-mm stainless-steel strip, compared with a claimed 0.15-mm limit at conventional domestic mills.
- SKSL reported H1FY27 revenue of Rs 102.71 crore and profit after tax of Rs 5.62 crore.
- SKSL’s H1FY27 EBITDA margin rose to 9.2% from 8.4% in H1FY26.
- SKSL plans a 1,150-mm 4-Hi AGC mill that management says could increase capacity by 2.5 times.
powered by IRIS

Shri Kanha Stainless Limited is targeting premium precision applications with 0.08-mm stainless-steel strips, compared with its claim that conventional domestic mills stop at 0.15 mm. SKSL reported H1FY27 profit after tax of Rs 5.62 crore, up 32.0% year on year, while presenting ultra-thin strip as a tolerance- and finish-led niche.
Know Shri Kanha Stainless inside out
Results, valuation, peers and who's buying, in one view.
Why does SKSL view 0.08-mm strip as a niche?
SKSL views 0.08-mm strip as a niche because it says conventional domestic units stall at 0.15 mm owing to machinery limits and process instability. The company positions 0.08 mm as ultra-thin material, compared with 0.20 mm at the standard end of its product spectrum, and identifies shaving blades as its primary target.
SKSL attributes this capability to its 20-Hi automatic gauge control, or AGC, rolling mill, which it says provides real-time gauge control across the full strip width. The presentation compares 0.08 mm with an approximately 0.07-mm human hair, but does not provide third-party technical validation, competitor names, market share or separate pricing data for ultra-thin material.
The company places precision electronics and surgical instruments alongside shaving blades in its target zone. Automotive and textile applications, sinks and appliances, and utensils and fabrication are shown elsewhere on the spectrum, indicating that SKSL’s 0.08-mm positioning sits within a broader portfolio rather than representing its entire sales base.
What stainless-steel products does SKSL manufacture?
SKSL manufactures coils, strips, circles and sheets in American Iron and Steel Institute, or AISI, 200, 300 and 400 series grades. Its coil and strip range spans 0.08 mm to 2.00 mm in thickness and 3.5 mm to 750 mm in width, covering ultra-thin precision products as well as wider industrial strip.
The company identifies surgical instruments, heat exchangers and high-speed lines as stated applications for coils and strips. Its circles range from 5 mm to 27 mm in outer diameter and are made on three cutting lines; SKSL says these blanks go directly to forming at utensil and component makers.
SKSL’s sheets have widths of 30 mm to 1,250 mm and use a polish line for elevators, kitchenware, sinks and fabricated products. This range shows that the company serves consumer-durable and industrial uses alongside precision markets, although the presentation does not disclose product-level revenue, volume, customer mix or realised prices.
How does SKSL support tolerance and finish requirements?
SKSL supports its claimed precision positioning through incoming inspection, slitting, two-stage cold rolling, bright annealing, and cutting and polishing. The company says mother coils receive chemical and mechanical testing, while cold rolling reduces material down to 0.08 mm before finishing operations.
The Reengus plant has a 29-inch 20-Hi AGC mill, two bright-annealing lines, one conventional annealing line, three slitting lines and one deburring line. SKSL says bright annealing uses a controlled atmosphere to restore ductility and shine, a process relevant to applications requiring finish as well as gauge control.
SKSL also lists three circle lines, one sheet line and one polish line, along with an in-house tensile laboratory, ISO 9001:2015 certification and Bureau of Indian Standards, or BIS, compliance. Its single integrated Reengus, Sikar facility has installed capacity of 14,000 metric tonnes per annum, employs about 81 people including 42 in production, and handles about 200 to 400 AISI-series grades.
Got a follow-up? Ask IRIS
How does SKSL sell its products and what do results show?
SKSL says it prices on tolerance and finish rather than tonnage, using dealer-cum-customer hubs, mid-node distributors and direct technical sales to original equipment manufacturers, or OEMs, and end users. The top 10 dealers accounted for 83% of sales, with the remaining 17% outside that group, indicating meaningful dealer concentration in the disclosed sales mix.
A confirmed order book of Rs 12.73 crore as of 25 November 2025 covered plate, sheet and strip. The disclosed figure provides near-term visibility across those product groups, but SKSL does not identify the portion related to 0.08-mm material, specify customers, or state expected delivery timing.
SKSL reported revenue of Rs 102.71 crore in H1FY27, the half year ended 30 September 2026. Revenue was 7.6% above Rs 95.42 crore in H2FY26 but 6.8% below Rs 110.23 crore in H1FY26, while profitability margins increased over both the year-on-year comparison and the sequential comparison.
Profit after tax rose 32.0% year on year to Rs 5.62 crore in H1FY27 from Rs 4.26 crore, while the margin rose to 5.5% from 3.9%. Earnings before interest, tax, depreciation and amortisation, or EBITDA, margin increased to 9.2% from 8.4%; SKSL specifies that EBITDA excludes other income.
Material margin, defined by SKSL as revenue less material cost, rose to 13.7% of sales from 11.6% in H1FY26. Finance cost fell 7.6% to Rs 2.28 crore from Rs 2.47 crore, and interest cover increased to 4.1 times from 3.7 times; the presentation does not attribute these changes specifically to ultra-thin strip sales.
How could the new mill change SKSL’s plan?
SKSL says a planned 1,150-mm 4-Hi AGC mill could increase capacity by 2.5 times and support export and OEM programmes. A 4-Hi mill is a four-high rolling configuration, while AGC is automatic gauge control; the plan is the company’s stated route for expanding beyond its current 14,000-metric-tonnes-per-annum facility.
Capital work in progress stood at Rs 3.63 crore in H1FY27, and SKSL reported no deviation in its use of initial public offering proceeds. SKSL listed on NSE Emerge in December 2025 with Rs 40.49 crore of net initial public offering proceeds, but the presentation does not state the new mill’s commissioning date, project cost, funding split, utilisation target or expected revenue contribution.
Management also identifies mandatory BIS certification as a shield against non-compliant imports and cites recyclability, longevity, urbanisation and infrastructure as demand factors. These are management-presented market considerations rather than sales forecasts, and their outcome depends on execution in the identified shaving-blade, electronics, surgical, export and OEM segments.
Conclusion
SKSL’s stated competitive position is built on producing 0.08-mm stainless-steel strip through its 20-Hi AGC rolling capability and related inspection, annealing and finishing processes. Its H1FY27 figures show higher margins and profit despite lower year-on-year revenue, but the presentation does not quantify how much of that result came from ultra-thin strip or premium applications.
The next disclosed development to watch is the planned 1,150-mm 4-Hi AGC mill, which management says could raise capacity by 2.5 times and enable export and OEM programmes. Future updates on project timing, capacity utilisation, the mix of 0.08-mm output and conversion of the Rs 12.73 crore order book would clarify how the niche plan is progressing.


